EN
User manual
Washer Dryer
ZKN 7147 J
• After having installed the appliance, check that it is not
standing on the inlet and drain hose and the worktop is
not pressing the electrical supply cable against the
wall.
• If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely
under the appliance.
tumble dry items which have been washed in water or
require airing.
• Plastic detergent dispensers should not remain in the
drum during the drying cycle, as the plastic used is not
designed to withstand the heat. If you wish to wash-
through-to-dry you should use the conventional deter-
gent dispenser drawer.
• Always be sure, that there is no water leakage from ho-
ses and their connections after the installation.
• Never pull the power supply cable to remove the plug
from the socket; always take hold of the plug itself.
• If the appliance is installed in a location subject to
frost, please read the “dangers of freezing” chapter.
• Any plumbing work required to install this appliance
should be carried out by a qualified plumber or compe-
tent person.
• Any electrical work required to install this appliance
should be carried out by a qualified electrician or com-
petent person.
• Never use your new appliance if the power supply ca-
ble, the control panel, the working surface or the base
are damaged so that the inside of the appliance is ac-
cessible.
Child safety
• This appliance is not intended for use by person (in-
cluding children) with reduced physical sensory or
mental capabilities or lack of experience and knowl-
edge unless they have been given supervision or in-
struction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they do
not play with the appliance.
• The packaging components (e.g. plastic film, polystyr-
ene) can be dangerous to children - danger of suffoca-
tion! Keep them out of children’s reach
• Keep all detergents in a safe place out of children’s
reach.
• Make sure that children or pets do not climb into the
drum. To prevent children and pets becoming trapped
inside the drum this machine incorporates a special
feature.
Use
• This appliance is designed for domestic use. It must
not be used for purposes other than those for which it
was designed.
• Only wash and dry fabrics which are designed to be
machine washed or dried. Follow the instructions on
each garment label
• Do not overload the appliance. See the Washing Pro-
gramme Table.
• Before washing, ensure that all pockets are empty and
buttons and zips are fastened. Avoid washing frayed or
torn articles and treat stains such as paint, ink, rust,
and grass before washing. Underwired bras must NOT
be machine washed.
• Garments which have been in contact with volatile pe-
troleum products should not be machine washed. If
volatile cleaning fluids are used, care should be taken
to ensure that the fluid is removed from the garment
before placing in the machine.
• As some duvets and eiderdowns should be washed/
dried in large commercial machines because of their
bulk, please check with the manufacturer of the item
before washing in a domestic machine.
• The users should always check that they have not left
their gas lighters (disposable or otherwise) in their
clothing.
• Never tumble dry items that have had contact with
chemicals such as dry cleaning fluid. These are of a
volatile nature and could cause an explosion. Only
To activate this device, ro- To disable this device and
tate the button (without
pressing it) inside the
door clockwise until the
groove is horizontal. If
necessary use a coin.
restore the possibility of
closing the door, rotate the
button anti-clockwise until
the groove is vertical.
3
Product description
1
2
3
4
5
6
Detergent dispenser drawer
Control panel
Door opening handle
Rating plate
Drain pump
Adjustable feet
1
2
3
4
5
6
Detergent dispenser drawer
Compartment for detergent used for prewash and soak
phase or for stain remover used during the stain action
phase (if available). The prewash and soak detergent is
added at the beginning of the wash programme. The stain
remover is added during the stain action phase.
Compartment for powder or liquid detergent used for
main wash. If using liquid detergent pour it just before
starting the programme.
Compartment for liquid additives (fabric softener,
starch).
Follow the product manufacturer’s recommendations on
quantities to use and do not exceed the «MAX» mark in the
detergent dispenser drawer. Any fabric softener or starch-
ing additives must be poured into the compartment before
starting the wash programme.
4
Control panel
On the following page there is a picture of the control panel. It shows the programme selector dial as well as the
buttons, pilot lights and the display. These are presented by relevant numbers on the following pages.
10
9
1
2
3
4
5
6
7
8
1
2
3
4
5
Programme selector dial
Spin button
Autodry button
Drying time button
Super quick button
6
7
8
9
Extra rinse button
Start/Pause button
Delay start button
Door pilot light
10 Display
Table of symbols
= Rinse hold
= Child Safety Lock
Automatic Dry
By pressing this button you can choose the required de-
gree of drying for cottons and synthetics:
• Cupboard dry (Cottons and Synthetics)
• Iron dry (Cottons)
The pilot light corresponding to the selected dryness de-
gree will illuminate.
1-8 Programme selector dial, spin speed button,
drying level and time, and available options
Programme Selector Dial
It allows you to switch the appliance on/off and/or to se-
lect a programme.
Spin
By pressing this button you can change the spin speed of
the selected programme or to select Rinse Hold option.
Drying Time
If you wish to carry out a timed drying programme, press
this button until the drying time you want appears on the
display according to the fabrics (cottons or synthetics)
you have to dry. For Cottons you can select a drying time
from 10 minutes to 250 minutes (4.10). For Synthetics
you can select a drying time from 10 minutes to 130 mi-
nutes (2.10). Every time you press this button the drying
time increases by 5 mins.
Rinse hold
By selecting this function the water of the last rinse is not
emptied out to prevent the fabrics from creasing. Before
opening the door it will be necessary to empty out the wa-
ter. To empty out the water, please read the paragraph «At
the end of the programme».
5
The display shows the following information:
10.1: Child safety lock
This device permits you to leave the appliance unattended
during it's functioning.
Available options:
Super Quick
Short cycle for lightly soiled items or for laundry which
needs only freshening up. We recommend you to reduce
the fabrics loading.
10.2:
• Duration of the selected programme
After selecting a programme, the duration is displayed
Extra Rinse
in hours and minutes (for example
). The dura-
This appliance is designed to save energy. If it necessary
to rinse the laundry using an extra quantity of water (extra
rinse), select this option. Some additional rinses will be
performed. This option is recommended for people who
are allergic to detergents, and in areas where the water is
very soft.
tion is calculated automatically on the basis of the
maximum recommended load for each type of fabric.
After the programme has started, the time remaining is
updated every minute.
• Selected drying time
After selecting a drying programme the drying time is
shown in minutes or hours and minutes. After the pro-
gramme has started, the time remaining is updated ev-
ery minute.
Start Pause
This button allows you to start or to interrupt the selected
programme.
Delay Start
• Delayed start
The Selected delay set by pressing the relevant button
appears on the display for a few seconds, then the du-
ration of the selected programme is displayed again.
The delay time value decreases by one unit every hour
and then, when 1 hour remains, every minute.
• Alarm codes
In the event of operating problems, some alarm codes
can be displayed, for example
«What to do if...»).
• Incorrect option selection
If an option which is not compatible with the set wash
programme is selected, the message Err is displayed at
the bottom of the display for a few seconds and the in-
tegrated red light of button 7 start flashing.
The programme can be delayed from 30 min - 60 min - 90
min, 2 hours and then by 1 hour up to a maximum of 20
hours by means of this button.
Door light
The pilot light 9 illuminates when the programme starts
and indicates if the door can be opened:
• light on: the door cannot be opened. The machine is
working or has stopped with water left in the tub.
• light off: the door can be opened. The programme is
finished or the water has been emptied out.
• light blinking: the door is opening in a few minutes.
(see paragraph
10 Display
• End of programme
When the programme has finished the flashing zero (
) is displayed, the pilot light 9 and the pilot light of
button 7 go out and the door can be opened.
10.1
10.2
6
Washing Programmes
Programme - Maximum and Minimum Temperature - Cycle De-
scription - Maximum Spin Speed - Maximum Fabrics Load -
Type of Laundry
Detergent Compart-
ment
Options
Cottons
90° - 60°
Main wash - Rinses
Maximum spin speed at 1400 rpm
Max. load 8 kg - Reduced load 4 kg1)
SPIN
RINSE HOLD
SUPER QUICK
EXTRA RINSE
White cotton(heavily and normally soiled items).
Cottons Eco
60° - 40°
Main wash - Rinses
SPIN
RINSE HOLD
EXTRA RINSE
Maximum spin speed at 1400 rpm
Max. load 8 kg
White or fast colour cotton (normally soiled items).
This programme can be selected for normally soiled cotton
items. The temperature will decrease and the washing time will
be extended. This allows to obtain a good washing efficiency by
saving energy.
Cottons
60° - 30°
Main wash - Rinses
Maximum spin speed at 1400 rpm
Max. load 8 kg - Reduced load 4 kg1)
SPIN
RINSE HOLD
SUPER QUICK
EXTRA RINSE
White or colour cotton (normally or slightly soiled items) .
2)
Cottons + Prewash
SPIN
60° - 40°
RINSE HOLD
SUPER QUICK
EXTRA RINSE
Prewash - Main wash - Rinses
Maximum spin speed at 1400 rpm
Max. load 8 kg - Reduced load 4 kg1)
White or colour cotton (heavily or normally soiled items)
Synthetics
60° - 30°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 4 kg - Reduced load 2 kg1)
SPIN
RINSE HOLD
SUPER QUICK
EXTRA RINSE
Synthetic or mixed fabrics: underwear, coloured garments, non-
shrink shirts, blouses.
7
Programme - Maximum and Minimum Temperature - Cycle De-
scription - Maximum Spin Speed - Maximum Fabrics Load -
Type of Laundry
Detergent Compart-
ment
Options
Easy iron
40°
Main wash - Rinses
SPIN
RINSE HOLD
EXTRA RINSE
Maximum spin speed at 900 rpm
Max. load 1 kg
Synthetic or mixed fabrics: selecting this programme the laun-
dry is gently washed and spun to avoid any creasing. In this way
ironing is easier. Furthermore the machine will perform addi-
tional rinses.
Delicates
40° - 30°
Main wash - Rinses
Maximum spin speed at 700 rpm
Max. load kg 4 - Reduced load kg 21)
RINSE HOLD
SUPER QUICK
EXTRA RINSE
Delicate fabrics: acrylics, viscose, polyester.
Wool / Handwash
40° - Cold
SPIN
RINSE HOLD
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2 kg
Washing programme for machine washable wool as well as for
hand washable woollens and delicate fabrics. Note! A single or
bulky item may cause imbalance. If the appliance doesn’t per-
form the final spin phase, add more items, redistribute the load
manually and then select the spinning programme.
Jeans
40°
SPIN
RINSE HOLD
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 4 kg
With this programme it is possible to wash items like pants,
shirts or jackets in denim tissue and also jersey realized with hi-
tech materials. Note! The Extra Rinse option will be activated au-
tomatically.
Sport Intensive
40°
SPIN
RINSE HOLD
Prewash - Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2,5 kg
This programme is suitable for washing heavily soiled sport
items. The appliance will add automatically a prewash phase be-
fore the main wash to eliminate mud stains.
8
Programme - Maximum and Minimum Temperature - Cycle De-
scription - Maximum Spin Speed - Maximum Fabrics Load -
Type of Laundry
Detergent Compart-
ment
Options
Rinses
SPIN
RINSE HOLD
EXTRA RINSE
Maximum spin speed at 1400 rpm
Max. load 8 kg
With this programme it is possible to rinse and spin cotton gar-
ments which have been washed by hand. The machine performs
3 rinses, followed by a final long spin.
Important!
The spin speed will automatically assume the setting for cotton
items. if required, reduce the speed to the desired level by
pressing the button 2.
Drain
Draining of water
Max. load 8 kg
For emptying out the water of the last rinse in programmes
which stop with water in the tub.
Spin
SPIN
Drain and long spin
Maximum spin speed at 1400 rpm
Max. load 8 kg
Separate spin for hand washed garments and after programmes
which stop with water in the tub. You can reduce the spin speed
to the required level by pressing the relevant button to adapt it
to the fabrics to be spun.
O/Off
For cancelling the programme which is running or to switch the
machine off .
1) If you select the Super Quick option by pressing button 5, we recommend that you reduce the maximum load as indicated. Full
loading is possible however with somewhat reduced cleaning results.
2) If using liquid detergents, a programme without PREWASH must be selected.
Automatic Drying programmes
Degree of Drying
Type of Fabric
Max Load
4 kg
Cupboard dry
Cotton and linen (bathrobes, bath
towels, etc)
Suitable for items to put away without ironing
Cupboard dry
Suitable for items to put away without ironing
Synthetics and mixed fabrics
(jumpers, blouses, underwear,
household linen)
3 kg
4 kg
Iron dry
Suitable for ironing
Cotton and linen (sheets, table-
cloths, shirts, etc.)
9
Timed Programmes
Suggested dry-
ing time (mi-
nutes)
Spin Speed
(rpm)
Degree of Drying
Type of Fabric
Drying Load
Cupboard dry
Suitable for items to put away with-
out ironing
Cotton and linen (bath-
robes, bath towels, etc)
6 kg
4 kg
2 kg
185 - 205
110 - 120
60 - 70
1400
900
Cupboard dry
Suitable for items to put away with-
out ironing
Synthetics and mixed
fabrics (jumpers, blou-
ses, underwear, house-
hold linen)
3 kg
1 kg
115-125
40-50
Cotton and linen
(sheets, tablecloths,
shirts, etc.)
6 kg
4 kg
2 kg
150 - 170
90 - 100
50 - 60
Iron dry
Suitable for ironing
1400
Hints for test institute
Test performance, in accordance with EN 50229, must be carried out with the a first drying load of 5 kg (load compo-
sition : pillowcase and towels) by selecting the TIMED DRYING programme for Cotton and setting 120 minutes.
The second drying load of 3 kg (load composition : 3 sheets and towels) must be tested by selecting the TIMED
DRYING programme for Cotton and setting 85 minutes.
Helpful hints and tips
Blood: treat fresh stains with cold water. For dried stains,
soak overnight in water with a special detergent then rub
in the soap and water.
Oil based paint: moisten with benzine stain remover, lay
the garment on a soft cloth and dab the stain; treat several
times.
Dried grease stains: moisten with turpentine, lay the gar-
ment on a soft surface and dab the stain with the fingertips
and a cotton cloth.
Sorting out the laundry
Follow the wash code symbols on each garment label and
the manufacturer’s washing instructions. Sort the laundry
as follows: whites, coloureds, synthetics, delicates, wool-
lens.
Before loading the laundry
Never wash whites and coloureds together. Whites may
lose their «whiteness» in the wash.
New coloured items may run in the first wash; they should
therefore be washed separately the first time.
Button up pillowcases, close zip fasteners, hooks and
poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special detergent or
detergent paste.
Rust: oxalic acid dissolved in hot water or a rust removing
product used cold. Be careful with rust stains which are
not recent since the cellulose structure will already have
been damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well (whites and fast
coloureds only).
Grass: soap lightly and treat with bleach (whites and fast
coloureds only).
Treat curtains with special care. Remove hooks or tie them
up in a bag or net.
Ball point pen and glue: moisten with acetone1), lay the
garment on a soft cloth and dab the stain.
Lipstick: moisten with acetone as above, then treat stains
with methylated spirits. Treat any residual marks with
bleach.
Removing stains
Stubborn stains may not be removed by just water and de-
tergent. It is therefore advisable to treat them prior to
washing.
1) do not use acetone on artificial silk
10
Red wine: soak in water and detergent, rinse and treat with
acetic or citric acid, then rinse. Treat any residual marks
with bleach.
If using liquid detergents, a programme without prewash
must be selected.
Your appliance incorporates a recirculation system which
allows an optimal use of the concentrated detergent.
Follow the product manufacturer’s recommendations on
quantities to use and do not exceed the «MAX» mark in
the detergent dispenser drawer.
Ink: depending on the type of ink, moisten the fabric first
with acetone1), then with acetic acid; treat any residual
marks on white fabrics with bleach and then rinse thor-
oughly.
Tar stains: first treat with stain remover, methylated spirits
or benzine, then rub with detergent paste.
Quantity of detergent to be used
The type and quantity of detergent will depend on the type
of fabric, load size, degree of soiling and hardness of the
water used.
Follow the product manufacturers’ instructions on quanti-
ties to use.
Use less detergent if:
• you are washing a small load
Detergents and additives
Good washing results also depend on the choice of deter-
gent and use of the correct quantities to avoid waste and
protect the environment.
Although biodegradable, detergents contain substances
which, in large quantities, can upset the delicate balance
of nature.
The choice of detergent will depend on the type of fabric
(delicates, woollens, cottons, etc.), the colour, washing
temperature and degree of soiling.
• the laundry is lightly soiled
• large amounts of foam form during washing.
Degrees of water hardness
All commonly available washing machine detergents may
be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics (60°C max) and
woollens
• liquid detergents, preferably for low temperature wash
programmes (60°C max) for all types of fabric, or spe-
cial for woollens only.
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in your
area can be obtained from the relevant water supply com-
pany, or from your local authority. If the water hardness
degree is medium or high we suggest you to add a water
softener following always the manufacturer’s instructions.
When the degree of hardness is soft, readjust the quantity
of the detergent.
The detergent and any additives must be placed in the ap-
propriate compartments of the dispenser drawer before
starting the wash programme.
Drying Hints
ers, quilts, sleeping bags and duvets must not be ma-
chine dried.
• Avoid drying dark clothes with light coloured fluffy
items such as towels as these can attract the fluff.
• Remove the laundry when the appliance has finished
drying.
• To avoid a static charge when drying is completed, use
either a fabric softener when you are washing the laun-
dry or a fabric conditioner specifically for tumble dry-
ers.
Preparing the drying cycle
As a dryer, the appliance works on the condensation prin-
ciple.
Therefore, the water tap must be open and the drain hose
must drain water into a sink or into the drain pipe, even
during the drying cycle.
Attention!
Before starting the drying programme, reduce the loads of
washed laundry, in order to obtain good performances.
Laundry not suitable for drying
• Garments padded with foam-rubber or materials simi-
lar to foam-rubber must not be machine dried; they
represent a fire hazard.
• Particularly delicate items such as synthetic curtains,
woollen and silk, garments with metal inserts, nylon
stockings, bulky garments such as anoraks, bed cov-
11
• Also, fabrics containing residue of setting lotions or
hair sprays, nail solvents or similar solutions must not
be machine dried in order to avoid the formation of
harmful vapours.
The detergent and any additives must be placed in the ap-
propriate compartments of the dispenser drawer before
starting the wash programme.
If using liquid detergents, a programme without prewash
must be selected.
Your appliance incorporates a re-circulation system which
allows an optimal use of the concentrated detergent.
Follow the product manufacturer’s recommendations on
quantities to use and do not exceed the «MAX» mark in
the detergent dispenser drawer.
•
= Do not tumble dry.
Drying cycle duration
The drying time may vary depending on:
• speed of the final spin
• dryness degree required (iron dry, store dry)
• type of laundry
• weight of the load size .
The average drying time for a timed drying are indicated in
the «Drying programmes» chapter. The experience will
help you to dry your laundry in a more suitable way, ac-
cording to the different fabrics. Take note of the duration
drying time of the already performed cycles.
Additional drying
If the laundry is still damp at the end of the drying pro-
gramme, select a short drying cycle again.
Garment labels
For drying, follow the indications given on the manufac-
turer’s labels:
Warning! Do not over dry the laundry in order to
avoid creasing of fabrics or garment’s shrinking.
•
•
•
= May be tumble dried
= Drying at high temperature
= Drying at reduced temperature
First use
• Ensure that the electrical and water connections
comply with the installation instructions.
• Remove the polystyrene block and any material
from the drum.
machine, to remove any manufacturing residue
from the drum and tub. Pour 1/2 a measure of
detergent into the main wash compartment and
start the machine.
• Before the first wash, run a cotton cycle at the
highest temperature without any laundry in the
Personalisation
by or cause damage to the appliance. This function re-
mains enabled also when the washing machine is not
working.
There are two different ways to set this option:
1. Before pressing button 7: it will be impossible to
start the machine.
2. After pressing button 7: it will be impossible to
change any other programme or option.
To enable or disable this option press simultaneously for
about 6 seconds buttons 2 and 3 until on the display, the
Acoustic signals
The machine is provided with an acoustic device, which
sounds in the following cases:
• at the end of the cycle
• if there is a fault.
By pressing the 3 and 4 buttons simultaneously for about
6 seconds, the acoustic signal is deactivated (except if
there is a fault). By pressing these 2 buttons again, the
acoustic signal is reactivated.
Child safety lock
This device permits you to leave the appliance unattended
so you do not need to worry that children might be injured
icon
appears or disappears.
12
Daily Use
Load the laundry
Turn the selector dial to position
gramme/to switch the machine OFF.
to reset the pro-
Open the door by carefully
pulling the door handle
outwards. Place the laun-
dry in the drum, one item
at a time, shaking them
out as much as possible.
Close the door.
At the end of the programme the selector dial must be
turned to position , to switch the machine off.
Important! If you turn the programme selector dial to
another programme when the machine is working, the red
pilot light of button 7 will blink 3 times and the
messageErr is displayed to indicate a wrong selection.
The machine will not perform the new selected
programme.
Make sure that no laundry
stays between the seal and
the door. There is a risk of
water leakage or damage
to the laundry.
Select the spin speed by pressing button 2
When selecting a programme, the appliance proposes au-
tomatically the maximum spin speed provided for that
programme. (See "Washing programmes" for the maxi-
mum allowed spin speed).
Press this button repeatedly to change the spin speed, if
you want your laundry to be spun at a different speed. The
relevant pilot light illuminates.
Measure out the detergent and the fabric softener
Select the available options by pressing the buttons
5 and 6
Depending on the programme, different options can be
combined. These must be selected after choosing the de-
sired programme and before starting the programme.
When these buttons are pressed, the corresponding pilot
lights illuminate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected, the inte-
grated red pilot light of the button 7 flashes 3 times and
the message Err is displayed.
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent required, pour it into the
For the compatibility among the washing programmes and
the options see chapter «Washing programmes».
main wash compartment
or in the appropriate com-
Start the programme by pressing button 7
partment if the selected programme/option it requires
(see more details in "Detergent dispenser drawer").
If required, pour fabric softener into the compartment
To start the selected programme, press this button; the
corresponding green pilot light stops blinking.
The pilot light 9 illuminates to indicate that the appliance
starts operating and the door is locked.
If you have chosen a delayed start, the machine will begin
the countdown.
marked
(the amount used must not exceed the
«MAX» mark in the drawer). Close the drawer gently.
Select the required programme by means of the
programme selector dial (1)
Turn the programme selector dial to the required pro-
gramme.
Important! If an incorrect option is selected, the message
Err is displayed for a few seconds and the red pilot light of
this button blinks 3 times.
The green pilot light of button 7 starts to flash. The selec-
tor dial can be turned either clockwise or anticlockwise.
13
Select the Delay Start by pressing button 8
Interrupting a programme
Before you start the programme, if you wish to delay the
start, press this button to select the desired delay.
The selected delay time value will appear on the display
for a few seconds, then the duration of the programme will
appear again.
You must select this option after you have set the pro-
gramme and before you start the programme.
You can cancel or modify the delay time at any moment,
before you press button 7.
Press the button 7 to interrupt a programme which is run-
ning, the corresponding pilot light starts blinking. Press
the button again to restart the programme.
Cancelling a programme
Turn the selector dial to
to cancel a programme which
is running. Now you can select a new programme.
Opening the door after the programme has started
First set the machine to pause by pressing the button 7.
If the pilot light 9 goes off, the door can be opened.
If the pilot light 9 remains lit, this means that the machine
is already heating or that the water level is too high. In any
case, do not force the door!
Selecting the delay start :
1. Select the programme and the required options.
2. Select the delay start by pressing button 8.
3. Press button 7:
If you cannot open the door but you need to open it,
- the machine starts its hourly countdown.
- the programme will start after the selected delay
has expired.
switch the machine off by turning the selector dial to
After a few minutes the door can be opened.
.
(Pay attention to the water level and temperature!).
After closing the door, it is necessary to select the pro-
gramme and options again and to press button 7.
Cancelling the Delay Start after having started the pro-
gramme:
1. Set the washing machine to PAUSE by pressing but-
ton 7.
At the end of the programme
2.
Press button 8 once. On the display will appear '.
The machine stops automatically. The blinking appears
on the display, the pilot light of button 7 and the pilot light
9 go off.
If a programme or an option that ends with water left in the
tub has been selected, the pilot light 9 remains on and the
door is locked to indicate that the water must be emptied
out before opening the door.
Before you empty out the water, the drum continues to run
at regular intervals until the water draining.
Follow the below instructions to empty out the water:
3. Press button 7 again to start the programme.
Important!
• The selected delay can be changed only after selecting
the washing programme again.
• The door will be locked throughout the delay time. If
you need to open the door, you must first set the wash-
ing machine to PAUSE by pressing button 7 and wait a
few minutes before opening the door. After you have
closed the door, press the same button again.
1.
Turn the programme selector dial to
.
Important! The Delay Start cannot be selected with the
draining programme.
2. Select the draining or spinning programme.
3. Reduce the spin speed if needed, by pressing the
relevant button.
4. Press button 7.
At the end of the programme, the door is released and can
Altering an option or a running programme
It is possible to change some options before the pro-
gramme carries them out.
Before you make any change, you must pause the washing
machine by pressing button 7.
be opened. Turn the programme selector dial to
switch the machine off.
to
Remove the laundry from the drum and carefully check
that the drum is empty. If you do not intend to carry out
another wash, close the water tap. Leave the door open to
prevent the formation of mildew and unpleasant smells.
Changing a running programme is possible only by reset-
ting it. Turn the programme selector dial to
and then
to the new programme position. Start the new programme
by pressing button 7 again.
The washing water in the tub will be not emptied out.
14
Use - Drying
6. Press button 7 to start the programme. The time re-
maining is updated every minute.
7. At the end of the programme, the buzzer sounds. The
blinking appears on the display. The door pilot
light 9 is on.
Drying only
Caution!
The recommended load size is 4 kg for cottons and linen
and 3 kg for synthetic items.
During the last minutes of the drying cycle the appli-
ance performs an anti-crease phase. Through this
time the door is locked. The display shows the blink-
By pressing Drying Time button it is also possible
to dry up to 6 kg of cotton items (see the «Drying
Programme » table).
ing
.
Caution!
At the end of the anti-crease phase the door pilot
light 9 is off.
The water tap must be open and the drain hose must be
positioned in the sink or connected to the drain pipe.
1. Load the laundry.
2. Select a spin cycle at the maximum spin speed al-
lowed for the type of laundry in order to obtain the
best drying performances.
If you wish to open the door before or during the
anti-crease phase or to interrupt it, press any button
or turn the programme selector dial to any programme po-
sition (except
).
8.
Turn the selector dial to the
the machine off.
position to switch
3. Select the drying programme for Cottons or Synthet-
ic in the Drying sector of the programme selector di-
al.
4. If you wish to select an automatic drying (for cottons
and synthetic items only), press the button 3 until
the pilot light corresponding to the required dryness
degree illuminates.
5. If you wish to select a timed drying, press the button
4 until the time you want appears on the display (see
the «Drying Programme» table). Every time you
press this button the drying time increases by 5 mi-
nutes.
9. Remove the laundry from the drum.
The different type of cottons (towelling, sheets,
shirts, and so on) or any laundry items rolling up
during the spinning phase may result in partial dryness. In
the exceptional case that at the end of the cycle the laun-
dry remains slightly wet, we suggest that you unfold the
rolled up items, redistribute them evenly in the drum and
select an additional drying cycle of 20-30 minutes.
If you set only 10 minutes of drying phase with the
drying time button (4), the appliance performs only
a cooling phase.
The programme time will automatically increase by
some minutes.
Use - Washing & Drying
4. Select the required options by pressing the relevant
buttons.
NON-STOP programme - Washing and Automatic
Drying
The maximum load size is 4 kg for cotton and 3 kg for
synthetic.
If possible, do not select a spin speed lower than
that proposed by the appliance to avoid too long a
drying time therefore saving energy.
Caution! Do not use a dosing device/ball when
carrying out a washing and drying programme.
In any case the reduction of the spin speed is only
possible after selecting drying.
For cottons and synthetic the lowest value you can
select is 900 r.p.m.
1. Load the laundry.
2. Add detergent and fabric softener.
3. Switch the machine on by turning the selector dial to
the set washing programme/fabric.
15
5. Set the dryness degree by pressing button 3. The
display shows the whole duration of the washing and
the set drying cycle.
6. Start the programme by pressing button 7. The time
remaining is updated every minute on the display.
3. Select the required options by pressing the relevant
buttons.
If possible, do not select a spin speed lower than
that proposed by the appliance to avoid too long a
drying time therefore saving energy.
7. At the end of the programme turn the selector dial to
In any case the reduction of the spin speed is only
possible after selecting drying.
The lowest values you can select are 900 r.p.m. for
cottons and synthetics and 700 r.p.m. for delicate
fabrics.
the
position to switch the machine off. Remove
the laundry.
NON-STOP programme - Washing and Timed
Drying
4. Set the drying time by pressing button 4. The display
shows the whole duration of the washing and the set
drying cycle.
The recommended load size is 4 kg for cotton and 3 kg for
synthetic.
It is also possible to dry up to 6 kg of cotton items
(see the «Drying Programme » table).
If you set a washing programme and only 10 mi-
nutes of drying cycle, the total duration displayed
includes also the unrolling and the cooling phase.
5. Start the programme by pressing button 7. The time
remaining is updated every minute on the display.
6. At the end of the programme turn the selector dial to
the O position to switch the machine off and remove
the laundry.
Caution! Do not use a dosing device/ball when
carrying out a washing and drying programme.
1. Load the laundry and add detergent and fabric soft-
ener.
2. Switch the machine on by turning the selector dial to
the set washing programme/fabric.
• To air-dry this type of fabrics when they are washed the
first time.
• To clean the filter.
• Perform one or more rinse cycles to wash the drum be-
tween the washing and drying of fabrics with different
colors.
• After the drying phase, thoroughly clean the empty
drum, the gasket and the door with a wet rag.
Fluff in the garments
During the WASHING AND/OR DRYING PHASE, certain
types of fabric, as sponge-cloth, sweatshirt, could release
fluff.
The released fluff could stick to the fabrics during the next
cycle.
This drawback increases with technical fabrics.
To prevent the lint in your clothes, it is recommended:
• To do not wash dark fabrics after you washed and dried
light colored fabrics (new sponge, sweatshirt especial-
ly) and vice versa.
Care and cleaning
according to the softening powder manufacturer's instruc-
tions. This will help to prevent the formation of lime de-
posits.
Warning! You must DISCONNECT the appliance
from the electricity supply, before you can carry out
any cleaning or maintenance work.
External cleaning
Descaling
Clean the exterior cabinet of the appliance with soap and
water only, and then dry thoroughly.
The water we use normally contains lime. It is a good idea
to periodically use a water softening powder in the ma-
chine. Do this separately from any laundry washing, and
16
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
appliance is hot. The water must be cold before you
clean the drain pump.
Proceed as follows:
Remove the drawer by
pressing the catch down- part of the additive com-
wards and by pulling it
out. Flush it out under a
tap, to remove any traces
of accumulated powder.
To aid cleaning, the top
Open the pump door.
Put a container below the recess of the drain pump to
collect the water that flows out.
partment should be re-
moved.
Cleaning the drawer recess
Having removed the draw-
er, use a small brush to
clean the recess, ensuring
that all washing powder
residue is removed from
the upper and lower part of
the recess.
Press the two levers and pull forward the drainage duct
to let the water flow out.
Replace the drawer and run the rinse programme with-
out any clothes in the drum.
Cleaning the pump
The pump should be inspected regularly and particularly
if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during draining
due to objects such as safety pins, coins etc. blocking
the pump;
When the container is full of water, put the drainage
duct back again and empty the container. Do steps 3
and 4 again and again until no more water flows out
from the drain pump.
• a problem with water draining is detected (see chapter
“What to do if...” for more details).
2
1
Warning!
Disconnect the mains plug from the mains socket.
1.
2. Do not remove the filter while the appliance oper-
ates. Do not clean the drain pump if the water in the
17
Caution! When the appliance is in use and
depending on the programme selected there can be
hot water in the pump.
Pull back the drainage duct.
Unscrew the filter and remove it.
Never remove the pump cover during a wash cycle, always
wait until the appliance has finished the cycle, and is
empty. When refitting the pump cover, ensure it is
securely re-tightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filters
Important! If the appliance doesn't fill, takes long to fill
with water, the starting button blinks yellow or the display
(if available) shows the relevant alarm (see chapter "What
to do if..." for more details), check if the water inlet filters
are blocked .
Remove fluff and objects from the pump.
To clean the water inlet filters:
• Turn off the water tap.
• Unscrew the hose from
the tap.
Make sure that the impeller of the pump can turn. If this
does not occur, contact the service centre.
• Clean the filter in the
hose with a stiff brush.
1
• Screw the hose back onto the tap. Make sure the
connection is tight.
2
Clean the filter under the water tap and put it back in the
pump into the special guides.
Make sure that you tighten correctly the filter to prevent
leakages.
• Unscrew the hose from the machine. Keep a rag
nearby because some water may flow.
• Clean the filter in the valve with a stiff brush or with
the piece of cloth.
Close the pump door.
18
Make sure that the temperature is more than 0 °C before
you use the appliance again.
The manufacturer is not responsible for damages caused
by low temperatures.
Emergency emptying out
If the appliance cannot drain the water, proceed as follows
to empty out the machine:
35°
45°
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has cooled down;
4. open the pump door;
• Screw the hose back to the machine and make sure
the connection is tight.
• Turn on the water tap.
5. place a container on the floor below the recess of the
drain pump;
6. press the two levers and pull forward the drainage
duct to let the water flow out;
7. when the container is full of water, put the drainage
duct back again and empty the container;
repeat this operation until water stops flowing out;
8. if necessary clean the pump (refer to the section
‘Cleaning the pump’ );
Frost precautions
If the machine is installed in a place where the tempera-
ture could drop below 0°C, remove the remaining water
from the inlet hose and the drain pump.
1. disconnect the mains plug from the mains socket.
2. close the water tap
3. unscrew the water inlet hose from the tap;
4. put the two ends of the inlet hose in a container and
let the water flow out of the hose.
9. close the drain pump door.
5. empty the drain pump as described in the ‘Emergen-
cy emptying out’ section.
When you drain the water with the emergency drain proce-
dure, you must activate again the drain system:
6. when the drain pump is empty, install the water inlet
hose again.
1. Put 2 litres of water in the main wash compartment
of the detergent dispenser.
2. Start the programme to drain the water.
Warning!
What to do if…
Certain problems are due to lack of simple maintenance or
oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Centre,
please carry out the checks listed below.
During machine operation it is possible that the red pilot
light of button 7 blinks, one of the following alarm codes
appears on the display and some acoustic signals sound
every 20 seconds to indicate that the machine is not work-
ing:
•
•
•
: problem with the water supply.
: problem with the water draining.
: door open.
Once the problem has been eliminated, press the button 7
to restart the programme. If after all checks, the problem
persists, contact your local Service Centre.
19
Problem
Possible cause/Solution
The door has not been closed.
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
The washing machine does not start:
• Replace the fuse.
The selector dial is not correctly positioned and/or the button 7 has not been
pressed.
• Please turn the selector dial and press the button 7 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The Child Safety Lock has been activated.
• Deactivate the Child Safety Lock.
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose or in the inlet valve filter are blocked.
The machine does not fill:
• Clean the water inlet filters (see ‘Cleaning the water inlet filters’ for more
details).
The door is not properly closed.
• Close the door firmly.
The end of the drain hose is too low.
• Refer to relevant paragraph in «Water drainage» section.
The machine fills then empties im-
mediately:
The drain hose is squashed or kinked.
• Check the drain hose connection.
The drain filter is clogged.
• Clean the drain filter.
An option or a programme that ends with the water still in the tub or that elimi-
nates all the spinning phases has been selected.
The machine does not empty and/or
does not spin:
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
20
Problem
Possible cause/Solution
Too much detergent or unsuitable detergent (creates too much foam) has been
used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see if it is
damp.
There is water on the floor:
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The filter has not been properly screwed in after cleaning action.
• Screw the filter fully in.
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
Unsatisfactory washing results:
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the door is released.
There is water in the drum.
The door will not open:
• Select drain or spin programme to empty out the water.
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
The machine vibrates is noisy:
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
21
Problem
Possible cause/Solution
The electronic unbalance detection device has cut in because the laundry is
not evenly distributed in the drum. The laundry is redistributed by reverse rota-
tion of the drum. This may happen several times before the unbalance disap-
pears and normal spinning can resume. If, after 10 minutes, the laundry is still
not evenly distributed in the drum, the machine will not spin. In this case, re-
distribute the load manually and select the spin programme.
Spinning starts late or the machine
does not spin:
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select the spinning
programme.
The machine is fitted with a type of motor which makes an unusual noise com-
pared with other traditional motors. This new motor ensures a softer start and
more even distribution of the laundry in the drum when spinning, as well as
increased stability of the machine.
The machine makes an unusual
noise:
Machines based on modern technology operate very economically using very
little water without affecting performance.
No water is visible in the drum:
The machine does not dry or does
not dry properly:
The drying time or the dryness degree has not been selected.
• Select the drying time or the dryness degree.
The water tap is not turned on.
• Open the water tap.
The drain filter is clogged.
• Clean the drain filter.
The machine is overloaded.
• Reduce the laundry load in the drum.
The selected drying programme, time or dryness degree was not suitable for
the laundry.
• Select the suitable drying programme, time or dryness degree for the laun-
dry.
The laundry is full of different col-
ored fluff:
The fabrics washed in the previous cycle released fluff of a different color (refer
to “Fluff in the garments” in chapter “Use - Washing & Drying”).
• The drying phase helps to eliminate some fluff.
• Clean the clothes with a fluff remover.
In case of an excessive amount of fluff in the drum repeat the following proce-
dure twice:
• Thoroughly clean the empty drum, the gasket and the door with a wet rag.
• Perform a rinse cycle.
• Put a wool or piled fabric rag inside the drum.
• Perform a drying cycle of 10 minutes.
• Remove the old wool cloth.
Now you can wash other garments.
22
If you are unable to identify or solve the problem, contact
our service centre. Before telephoning, make a note of the
model, serial number and purchase date of your machine:
the Service Centre will require this information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ...
Technical data
Dimensions
Width
Height
Depth
60 cm
85 cm
63 cm
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate, on the
inner edge of the appliance door.
Water Supply Pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Cotton
8 kg
Maximum Dry Load
Cotton
Cotton Big Capacity
Synthetic
4 Kg
6 Kg
2 Kg
Spin Speed
Maximum
1400 rpm
Consumption values
Programme
Energy consumption
Water consumption (litres) Programme duration (Mi-
nutes)
(KWh)
White Cottons 90°
Cottons 60°
2.6
69
65
1.6
Cotton Energy Saving Pro-
gramme 60° 1)
1.05
57
For the duration of the pro-
grammes, please refer to
the display on the control
panel.
Cottons 40°
0.95
0.60
0.70
0.35
65
55
69
58
Synthetics 40°
Delicates 40°
Wool/ Handwash 30°
1) «Cotton Energy Saving programme » at 60°C with a load of 7 kg is the reference programme for the data entered in the energy label,
in compliance with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on the
quantity and type of laundry, on the inlet water temperature and on the ambient temperature.
23
Installation
Unpacking
Positioning
All transit bolts and packing must be removed before us-
ing the appliance.
Install the machine on a flat hard floor. Make sure that air
circulation around the machine is not impeded by carpets,
You are advised to keep all transit devices so that they can rugs etc. Check that the machine does not touch the wall
be refitted if the machine ever has to be transported again.
or other kitchen units. Level the washing machine by rais-
ing or lowering the feet. The feet may be tight to adjust as
they incorporate a self locking nut, but the machine MUST
be level and stable.
Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, noise and displace-
ment of the machine during operation. Never place card-
board, wood or similar materials under the machine to
compensate for any unevenness in the floor.
After removing all the
packaging, carefully lay
Remove the power supply
cable and the hoses from
If necessary, check the
setting with a spirit level.
machine on it's back to re- the hose holders on the
move the polystyrene base rear of the appliance.
from the bottom.
Installation on suspended flooring
Suspended wooden floors are particularly susceptible to
vibration.
To help prevent vibration we recommend you place a wa-
terproof wood panel, at least 15 mm thick under the appli-
ance, secured to at least 2 floor beams with screws, the
wood panel must extend beyond the front feet.
If possible install the appliance in one of the corners of
the room, where the floor is more stable.
Unscrew the three bolts.
Slide out the relevant plas-
tic spacers.
Rubber feet kit (4055126249)
Available from your authorized dealer.
The rubber feet are particularly recommended on floating,
slippery and wooden floors.
Mount the rubber feet to prevent vibration, noises and dis-
placement of the appliance during operation.
Read carefully the instructions supplied with the kit.
Open the porthole and re- Fill the smaller upper hole
move the polystyrene
block fitted on the door
seal.
and the two large ones
with the corresponding
plastic plug caps supplied
in the bag containing the
instruction booklet.
Water inlet
Warning! This appliance must be connected to a
cold water supply
24
Caution! Before connecting up the appliance to new
pipework or to pipework that has not been used for
some time, run off a reasonable amount of water to flush
out any debris that may have collected
There should be a minimum vertical distance of 5.02 m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.
Water drainage
Caution! Do not use the hose from your previous
appliance to connect to water supply.
This appliance is designed to be permanently plumbed in-
to your home's drainage system using one of the follow-
ing methods.
The inlet hose is screwed to the back of the appliance.
1. Into a drainage standpipe.
Connect the hose to a tap
with a 3/4” thread. Always
use the hose supplied with
the appliance.
Firstly form a hook in the end of the drain hose using
the “U” piece” supplied.
“U” piece supplied
Place the drain hose into your standpipe, which should
have an internal diameter of approximately 38 mm thus
ensuring there is an air break between the drain hose
and standpipe.
35°
45°
When discharging into a standpipe ensure that the top
of the standpipe is no more than 90 cm (35.4'') and no
less than 60 cm (23.6'') above floor level.
The other end of the inlet hose which connects to the
appliance can be turned as showed in the picture.
Do not place the inlet hose downwards. Angle the hose
to the left or right depending on the position of your
water tap. Set the hose correctly by loosening the ring
nut. After positioning the inlet hose, be sure to tighten
the ring nut again to prevent leaks.
38 mm (1.5”)
standpipe
diamater
30 cm (12”)
Caution! The inlet hose must not be lengthened. If it
is too short and you do not wish to move the tap,
you will have to purchase a new, longer hose specially
designed for this type of use.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece is
available from your local Service Force Centre. The
joining piece must have an internal diameter of 18 mm.
Warning! Installation should comply with local
water authority and building regulations’
requirements.
The appliance must be connected to a cold water supply.
A minimum water pressure of 0.05 MPa (0.5 bar) is
required for safe operation of the appliance.
If you cannot make the cold water connection direct from
the rising mains, you may be able to operate the appliance
from your cold water storage system.
25
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
In the interest of the environment
The appliance should be connected to the FOUL drainage
system, the water will then be taken to a sewage works for
treatment before being discharged safely into a river.
It is essential that these appliances are not connected to
the surface water drainage system as this water is dis-
charged directly into a river or stream and may cause pol-
lution.
Min. 60 cm (23.6”)
Max. 90 cm (35.4”)
If your drain hose looks
like this (see beside) you
do not require the “U”
piece”. Just push the hose
firmly in to the standpipe.
If you require any further advice please contact your local
water authority.
SHOWER
2. Onto a sink outlet spigot.
TOILET
SINK
BATH
BIDET
WASHING
MACHINE
DISHWASHER
RAINWATER
‘RUN-OFF’
Loop
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
FOUL SEWERS
SEWAGE TREATMENT
WORKS
TREATED DISCHARGE
RIVER
UNTREATED
DISCHARGE
If the outlet spigot has not Push the drain hose onto
been used before, remove the spigot and secure with
RIVER
any blanking plug that
may be in place.
a clip, ensure a loop is
formed in the drain hose
(see above) to prevent
waste from the sink enter-
ing the appliance.
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or compe-
tent person.
If you intend to drain the hose from the machine into a
sink, make sure that the sink is empty and the plug hole
is not blocked. Use the plastic “U - Piece” supplied.
Warning! THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should this
safety measure not be observed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate.
Special conditions
If the floor is carpeted or covered with crumbly or soft ma-
terial, insert a rigid support base under the feet to prevent
noise, vibration or displacement. The base should pro-
trude a few centimetres beyond the edges of the appliance.
Warning! Information on the electrical connection is
given on the rating plate on the inner edge of the
appliance door.
Warning! The appliance should NOT be placed on
deep pile carpeting.
Note!
The appliance is supplied with a 13 amp plug fitted.
26
In the event of having to change the fuse in the plug sup-
plied, a 13 amp ASTA approved (BS1363/A) fuse must be
used.
MUST be carried out by our Service Force Centre. The
appliance should not be connected to the electrical supply
by means of an extension cable.
Warning! A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of safely. Should
the appliance power supply cable need to be replaced, this
Note!
When the appliance is installed the power supply cable
must be accessible.
Environmental concerns
>PP<=polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed
information about recycling of this product, please contact
your local council, your household waste disposal service
or the shop where you purchased the product.
Ecological hints
To save water, energy and to help protect the environment,
we recommend that you follow these tips:
• Normally soiled laundry may be washed without pre-
washing in order to save detergent, water and time (the
environment is protected too!).
• The machine works more economically if it is fully loa-
ded.
• With adequate pre-treatment, stains and limited soiling
can be removed; the laundry can then be washed at a
lower temperature.
Packaging materials
• Measure out detergent according to the water hard-
ness, the degree of soiling and the quantity of laundry
being washed.
The materials marked with the symbol
>PE<=polyethylene
>PS<=polystyrene
are recyclable.
27
|
