GAS HOB
MODE L ZGF 782
INSTRUCTION BOOKLE T
Please read this instruction booklet before using the appliance
Con t en t s
For the Installer
For the User
Tech n ical Dat a
Page 1 0
Descript ion
of t h e Hob
Page 5
Page 6
Im port an t Safet y
Requ irem en t s
Operat ion
Page 1 1
Page 1 2
Page 1 2
Page 1 3
Main t en an ce
an d Clean in g
In st allat ion
Page 7
Page 8
Page 8
Page 9
Gas Con n ect ion
Bu ildin g In
Som et h in g
Not Work in g
Elect rical Con n ect ion Page 1 4
Service an d
Spare Part s
Wirin g Diagram
Fau lt Fin din g
Com m ission in g
Servicin g
Page 1 5
Page 1 6
Page 1 8
Page 1 9
Peace of Min d
for 2 4 Mon t h s
Con version from
n at u ral gas t o LPG
Page 1 9
This appliance complies with the following
E.E.C. Directives:
* 73/23 - 90/683
Guide to Use the instructions
(Low VoltageDirective);
The following symbols will be found in the text to
guide you throughout the Instructions:
* 93/68 (General Directives);
* 89/336 (Electromagnetical
Compatibility Directive);
* 90/396 (Gas Appliances),
and subsequent modifications
Safety Instructions
Step by step instructions for an
☞
operation
Hints and Tips
i
Enviromental information
4
Descript ion of t h e Hob
4
3
2
3
5
1
6
7
8
9
10
11
1. Hob Top
2. Auxiliary Burner
3. Semi-rapid Burners
4. Ultra-rapid Double-crown Burner
5. Rapid Burner
6. Ignition pushbutton
7. Control knob for front left burner (auxiliary)
8. Control knob for back left buner (semi-rapid)
9. Control knob for central burner (ultra-rapid)
10. Control knob for back right burner (semi-rapid)
11. Control knob for front right burner (rapid)
INSTALLATION
WHEN THE HOB IS FIRST INSTALLED
Any gas installation must be carried out by
a registered CORGI installer, and in
accordance with existing rules and
regulations.
Once the hob has been installed, it is
important to remove any protective
materials, which were put on in the factory.
The relevant instructions are to be found in the
second section of this manual.
Please, ensure that, once the hob is
installed, it is easily accessible for the
engineer in the event of a breakdown.
5
Operat ion
HOB BURNERS
To light a burner, push the relevant control knob in,
turn it anticlockwise to maximum position, and
depress the ignition pushbutton marked by a small
electric spark symbol. Then adjust the flame as
required.
If the burner does not ignite, turn the control knob to
zero, and try again.
To ensure maximum burner efficiency, you should
only use pots and pans with a flat bottom fitting the
size of the burner used (see table).
Burner
minimum maximum
diameter
diameter
Ultra-rapid
(Double-crown)
Large (rapid)
Medium (semi-rapid) 120 mm.
Small (Auxiliary) 80 mm.
160 mm.
160 mm.
260 mm.
240 mm.
220 mm.
160 mm.
If you use a saucepan which is smaller than
the recommended size, the flame will
spread beyond the bottom of the vessel,
causing the handle to overheat.
As soon as a liquid starts boiling, turn down
the flame so that it will barely keep the
liquid simmering.
i
Using the Wok Stand
A wok stand is provided to enable you to use a round
bottomed wok on the hob. The wok stand must only
be used on the central burner, and should not be used
with any other type of wok or pan.
When fitting the wok stand, ensure the recesses in the
frame fit securely onto the bars of the pan supports,
as shown in the diagram.
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
If the control knobs become difficult to
turn, please contact your local Zanussi
Service Force Centre.
6
Main t en an ce an d Clean in g
Before any maintenance or cleaning can be
carried out, you must DISCONNECT the
hob from the electricity supply.
The hob is best cleaned whilst it is still warm, as
spillage can be removed more easily than if it is left
to cool.
The Hob Top
Regularly wipe over the hob top using a soft cloth
well wrung out in warm water to which a little
washing up liquid has been added. Avoid the use of
the following:
- household detergent and bleaches;
FO 2030
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
Fig. 1
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob
Brite or Bar Keepers Friend is used.
Pan Supports and Wok Stand
To keep the pan supports in the correct position, they
are hooked into hinges at the back of the hob.
The pan supports can be lifted for easier cleaning, as
shown in fig. 1.
To remove the pan supports completely, proceed as
shown in fig. 2.
The pan supports and the Wok Stand are dishwasher
proof. If washing them by hand, take care when
drying them as the enamelling process occasionally
leaves rough edges. If necessay, remove stubborn
FO 2032
stains using a paste cleaner.
Fig. 2
The Burners
The burner caps and crowns can be removed for
cleaning.
Wash the burners taps and crowns using hot soapy
water, and remove marks with a mild paste cleaner. A
well moistened soap impregnated steel wool pad can
be used with caution, if the marks are particularly
difficult to remove.
After cleaning, be sure to wipe dry with a soft cloth.
7
Som et h in g Not Work in g?
If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi
Service Force Centre.
SYMPTOM
SOLUTION
■ There is no spark when lighting the gas
◆ Check that the unit is plugged in and the electrical
supply is switched on
◆ Check that the RCCB has not tripped (if fitted)
◆ Check the mains fuse has not blown
◆ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
■ The gas ring burns unevenly
◆ Check the main jet is not blocked and the burner
crown is clear of food particles.
◆ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
In-guarantee customers should ensure that the
above checks have been made as the engineer will
make a charge if the fault is not a mechanical or
electrical breakdown.
If after all these checks, your hob still does not
operate correctly, contact your local Zanussi Service
Force Centre.
Please note that it will be necessary to provide proof
of purchase for any in-guarantee service calls.
Service an d Spare Part s
If you require spare parts or an engineer contact your
local Service Force Centre by telephoning:
CUSTOMER CARE
For general enquiries concerning your Zanussi
appliance, contact our Customer Care Department by
letter or telephone as follows:
0990-929929
Customer Care Department
Zanussi House
Hambridge Road
Newbury, Berks, RG14 5EP
Tel: 01635 - 521313
Your call will be routed to the Service Centre
covering your post code area. For further details,
please see the accompanying Customer Care Booklet.
When you contact the Service Centre, they will need
the following information:
1. Your name, address and post code.
2. Your telephone number
3. Clear and concise details of the fault
4. The model and the serial number (see rating label
on the back of this instruction booklet)
5. Date of purchase
8
Peace of Min d for 2 4 Mon t h s
ZANUSSI GUARANTEE CONDITIONS
Eu ropean Gu aran t ee
If you should move to another country within Europe
then your guarantee moves with you to your new
home subject to the following qualifications:
We, Zanussi, undertake that if, within 24 months of
the date of the purchase, this Zanussi appliance or
any part thereof is proved to be defective by any
reason only of faulty workmanship or materials, we
will, at our option, repair or replace the same FREE
OF ANY CHARGE for labour, materials or carriage
on condition that:
* The guarantee starts from the date you first
purchased your product.
* The guarantee is for the same period and to the
same extent for labour and parts as exist in the
new contry of use for this brand or range of
products.
* The appliance has been correctly installed and
used only on the gas and electricity supply stated
on the rating plate.
* This guarantee relates to you and cannot be
transferred to another user.
* The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer's instructions.
* Your new home is within the European
Community (EC) or European Free Trade Area.
* The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any
person not authorised by us.
* The product is installed and used in accordance
with our instructions and is only used
domestically, i.e. a normal household
* All service work under this guarantee must be
undertaken by a Zanussi Service Force Centre.
* The gas type and the gas supply pressure comply
with the specification given in the rating label
* Any appliance or defective part replaced shall
become the Company's property.
* The product is installed taking into account
regulations in your new country.
* This guarantee is in addition to your statutory and
other legal rights.
Before you move, please contact your nearest
Customer Care centre, listed below, to give them
details of your new home. They will then ensure that
the local Service Organisation is aware of your move
and able to look after you and your appliances.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visit may be available outside
these hours, in which case a premium will be
charged.
France
Senlis
+33 (0)3 44 62 29 99
Germany Nürnberg +49 (0)911 323 2600
Exclu sion s
Italy
Pordenone +39 (0)1678 47053
Stockholm +46 (0)8 738 79 50
Newbury +44 (0)1635 521 313
This guarantee does not cover:
Sweden
UK
* Damage or calls resulting from transportation,
improper use or neglect, the replacement of any
light bulbs or removable parts of glass or plastic.
* Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside the United Kingdom.
* Appliances found to be in use within a
commercial or similar environment, plus those
which are the subject to rental agreements.
* Products of Zanussi manufacture which are not
marketed by Zanussi.
9
In st ru ct ion s for t h e In st aller
Engineer technical data
OVERALL DIMENSIONS
SUPPLY CONNECTIONS
Gas:
Width:
Depth:
Height:
Weight:
680 mm.
510 mm.
72 mm.
12 Kg.
RC 1/2 inch (1/2 inch male) Rear right hand corner
Electric:
240V 50Hz supply, 3 core flexible cable with non
rewireable plug fitted with a 3 amp cartridge fuse.
CUT OUT DIMENSIONS
Width:
Depth:
560 mm.
480 mm.
Thickness: 30 mm.
Ign it ion HT Spark
Spark Generator Ispra Control's BF 50066 - 240V 0.6 YA T 120
Spark Gap Fixed
Rear Left Burner (semi rapid)
Rear Right Burner (semi rapid)
Heat Input 2.0 kW (6824 BTU/HR)
Heat Input 2.0 kW (6824 BTU/HR)
Front Left Burner (auxiliary)
Front Right Burner (rapid)
Heat Input 3.0 kW (10236 BTU/HR)
Heat Input 1.0 kW (3412 BTU/HR)
Central Burner (Ultra-rapid Double-crown)
Heat Input 3.5 kW (11942 BTU/HR)
BURNER
RAPID
(large)
SEMI-RAPID
(medium)
AUXILIARY
(small)
ULTRA-RAPID
(double-crown)
POSITION
MAX
MIN
MAX
MIN
MAX
MIN
MAX
MIN
NOMINAL THERMAL
POWER
kW
3.0
0.65
2.0
0.45
1.0
0.33
3.5
1.2
NOMINAL FLOW
RATE
m3/h
0.286
119
0.062
0.190
96
0.043
0.095
70
0.031
0.333
136
0.114
NOZZLE REFERENCE
1/100 mm
Adjust.
Adjust.
Adjust.
Adjust.
NOMINAL THERMAL
POWER
kW
2.8
0.65
2.0
0.45
1.0
0.33
3.5
1.2
NOMINAL FLOW
RATE
g/h
202
86
47
40
144
71
32
32
72
50
24
28
252
93
86
56
NOZZLE REFERENCE
1/100 mm
APPLIANCE CLASS : 3
Burner
Dia. Tap By-pass
1/100 mm
Tap colour
APPLIANCE
CATEGORY: II2H3+
Auxiliary
Semi-rapid
Rapid
28
32
40
56
Green
Green/Blue
Green/Black
Black/Red
APPLIANCE
GAS SUPPLY: Natural gas G20 / 20mbar
Ultra-rapid
Aeration adjustment none
10
Im port an t safet y requ irem en t s
This hob must be installed in accordance with the Gas
Safety (Installation and Use) Regulations (Current
Edition) and the IEE Wiring Regulations (Current
Location
Edition).
The hob may be located in a kitchen, a kitchen/diner
or bed sitting room, but not in a bathroom or shower
room.
Detailed recommendations are contained in the
following British Standards Codes Of Practice: B.S.
6172/ B.S. 5440, Part 2 and B.S. 6891 Current
Editions.
Before making the cut out in the worktop ensure that
the edges of the hob that are to be near either a side or
rear wall have a minimum distance of 55 mm.
between the edge of the hob and the wall.
The minimum distance combustible material can be
fitted above the hob in line with the edges of the hob
is 420 mm. If it is fitted below 420 mm. a space of 50
mm. must be allowed from the edges of the hob.
The minimum distance combustible material can be
fitted directly above the hob is 700 mm.
The hob should not be installed in a bed sitting room
with a volume of less than 20 m3. If it is installed in a
room of volume less than 5 m3 an air vent of effective
area of 110 cm2 is required. If it is installed in a room
of volume between 5 m3 and 10 m3 an air vent of
effective area of 50 cm2 is required, while if the
volume exceeds 11 m3 no air is required.
However, if the room has a door which opens directly
to the outside no air vent is required even if the
volume is between 5 m3 and 11 m3.
A minimum distance of 100 mm. must be left
between the side edges of the hob and any adjacent
cabinets or walls.
If there are other fuel burning appliances in the same
room, B.S. 5440 Part 2 Current Edition, should be
consulted to determine the requisite air vent
requirements.
Im port an t
If a 60 cm cooker hood is be installed above the hob,
ensure a minimum distance of 780 mm is left
between the hanging furniture units beside the cooker
hood (see diagram below).
INSTALLATION GUIDANCE INSTRUCTIONS
CLEARANCES REQUIRED
INSTALLATION GUIDANCE INSTRUCTIONS
CLEARANCES REQUIRED
WHEN FITTING THE GAS HOB
WITH A COOKER HOOD ABOVE
WHEN FITTING THE GAS HOB
WITHOUT A COOKER HOOD ABOVE
600 mm
780 mm min.
700 mm
650 mm
400 mm
400 mm
55 mm
50 mm
400 mm
50 mm
400 mm
100 mm
100 mm
50 mm
50 mm
FO 2231
FO 2027
11
In st allat ion
IMPORTANT
This hob must be installed by qualified
personnel to the relevant British Standards.
Any gas installation must be carried out by
a registered CORGI installer.
The manufacturer will not accept liability,
should the above instructions or any of the
other safety instructions incorporated in this
book be ignored.
On the end of the shaft, which includes the GJ 1/2"
threaded elbow, adjustment is fixed so that the washer
is fitted between the components as shown in the
diagram. Screw the parts together without using
excessive force.
Gas Connection
Connection to the gas supply should be with either
rigid or semi-rigid pipe, i.e. steel or copper.
The connection should be suitable for connecting to
RC 1/2 (1/2 BSP male thread).
When the final connection has been made, it is
essential that a thorough leak test is carried out on the
hob and installation.
FO 0264
A) End of shaft with nut
B) Washer
C) Elbow
Ensure that the main connection pipe does not exert
any strain on the hob.
It is important to install the elbow correctly,
with the shoulder on the end of the thread,
fitted to the hob connecting pipe.
Failure to ensure the correct assembly will
cause leakage of gas.
Rect an gu lar cu t -ou t size for h ob
Cut O ut Size
The dimensions of the cut-out are given in the
diagram.
55 min.
480
560
150 min
Dimensions are given in mm.
FO 2038
12
Bu ildin g In
Building over a cupboard or drawer
If the hob is to be installed above a cupboard or
drawer it will be necessary to fit a heat resistant board
below the base of the hob on the underside of the
work surface.
It is also recommended to carry out the electrical
connection to the hob as shown in diagrams 1 and 2.
ON/OFF SWITCH
ON/OFF SWITCH
2
1
3
a
60
FLEX
OUTLET
b
FLEX
OUTLET
FO 0764
FO 1013
FO 0763
Dimensions are given in mm.
Building over a kitchen unit with door
Proper arrangements must be taken in designing the
furniture unit, in order to avoid any contact with the
bottom of the hob which can be heated when it is
operated. The recommended solution is shown in
diagram 3.
The panel fitted under the hob ("a") should be easily
removable to allow easy access if technical assistance
is needed. The space behind the kitchen unit ("b") can
be used for connections.
Fitting the Hob into the worktop
50
50
Carry out the building in of the hob as follows:
• put the seals supplied with the hob, on the
FO 2039
edges of the cut out: place them exactly on
☞
the front and rear edge and at 50 mm. from
the side edges, as shown in the diagram, taking
care that the seals meet without overlapping;
• place the hob in the cut out, taking care that it
is centred;
• fix the hob with the relevant fixing clamps
and screws, as shown in the diagram. When
the screws have been tightened, the excess
seal can be removed.
Seal
a
The edge of the hob forms a double seal which
prevents the ingress of liquids.
FO 0199
13
Elect rical con n ect ion s
Permanent Connection
Any electrical work required to install this
hob should be carried out by a qualified
electrician or competent person, in
In the case of a permanent connection, it is necessary
that you install a double pole switch between the hob
and the electricity supply (mains), with a minimum
gap of 3 mm. between the switch contacts and of a
type suitable for the required load in compliance with
the current electric regulations.
accordance with the current regulations.
THIS HOB MUST BE EARTHED.
The switch must not break the yellow and green earth
cable at any point.
Th e m an u fact u rer declin es an y liabilit y
sh ou ld t h ese safet y m easu res n ot be
observed.
Ensure that the hob supply cord does not
come into contact with surfaces with
temperatures higher than 50 deg. C.
Th is h ob is design ed t o be con n ect ed t o a
2 4 0 V 5 0 Hz AC elect rical su pply.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the hob rating
plate. The rating plate is located on the bottom of the
hob. A copy is attached on the back cover of this
book.
The hob is supplied with a 3 core flexible supply cord
incorporating a 3amp plug fitted. In the event of
having to change the fuse, a 3amp ASTA approved
(BS 1362) fuse must be used.
Should the plug need to be replaced for any reason,
the wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow - Earth
Blue
Brown
- Neutral
- Live
— Connect the green and yellow (earth) wire to
the terminal in the plug which is marked with
☞
the letter 'E' or the earth symbol
coloured green and yellow.
or
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N'
or coloured black.
— Connect the brown (live) wire to the terminal
in the plug which is marked with the letter 'L'
or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
FO 0390
A cut off plug inserted into a 13 amp
socket is a seriuos safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
14
Wirin g Diagram
L
1
2
3
4
5
6
A
0
220/240
B
N
A. IGNITOR SWITCH
B. IGNITOR UNIT
15
Fau lt Fin din g
Prelim inary Electrical System s Check
PLUG (with cover removed)
SOCKET
(face view)
Earth Wire
Green/Yellow
( )
( )
E
Blue
Brown
Green
Yellow
START
Neutral Wire
Blue
Isolate appliance
and carry out:
A: Earth Continuity
check.
N
L
Blue
Green
Yellow
Brown
Carry out:
D: Resistance to
Earth check.
Electricity supply
should now be
satisfactory.
NO
YES
Carry out:
C: Polarity check.
A. EARTH CONTINUITY CHECK -
Appliance must be electrically
Has inlet fuse blown?
disconnected - meter set on Ω (Ohms) x 1
scale and adjust zero if necessary.
NO
YES
a) Test leads from any appliance earth point
to earth pin on plug. Resistance should
be less than 0.1 Ω (Ohm), check all earth
wires for continuity and all contacts clean
and tight.
Inlet wiring
faulty.
Rectify any
fault.
B. INSULATION CHECK - Appliance
electrically disconnected, all switches ON.
a) meter set on Ω (Ohms) x 1 scale.
Test leads from L to N in appliance
terminal block. If meter reads «0» then
there is a short circuit.
Isolate appliance and
carry out:
B: Insulation check.
Rectify any fault
including replacing
fuses as necessary.
b) meter set on Ω (Ohm) x 100 scale.
Repeat test with leads from L to E. If meter
reads less than ∞ (infinity) there is a fault.
NOTE - Should it be found that the fuse
has failed but no fault is indicated - a
detailed continuity check (i.e. by
disconnecting and checking each
component) is required to trace the faulty
component.
It is possible that a fault could occur as a
result of local burning/arcing but no fault
could be found under test. However a
detailed visual inspection should reveal
evidence of burning around the fault.
16
Ignition System / Gas Ignition
YES
Check gas supply at
burner
Ignitor does not spark
NO
Check plug top fuse and
replace if necessary
Light burner manually
Check by pass simmer
adjusted
Check polarity and earth
continuity of supply point
Check position of the
electrode
Check earth continuity
of appliance
Check fitting of burners
Check continuity from the tip of
each electrode to the terminals 1
to 4 on the ignitor unit
Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit
Check continuity from 'L' on the
mains connector block and the
taps ignition switches
Check for breaks in the insulation
of the HT leads
Check continuity from ignition
switches connector to ignitor unit
Change the taps ignition
switches
Change the ignitor unit
17
Com m ission in g
When the hob has been fully installed it will be
necessary to check the minimum flame setting. To do
this, follow the procedure below.
- Turn the gas tap to the MAX position and ignite.
- Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times.
If the flame is unstable or is extinguished follow the
procedure below.
Procedure:
Re-ignite the burner and set to MIN.
Remove the control knob, insert a thin
☞
bladed screwdriver down the centre of the
gas tap control shaft and turn the adjustment
screw until the flame is steady and does not
extinguish, when the knob is turned from
MIN to MAX. Repeat this procedure for all
burners.
Pressu re Test in g
Remove left hand pan support and front left
burner cap and crown.
☞
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite
another burner.
The pressure reading should be nominally
20mbar and must be between 17 mbar and
25mbar.
Turn off the burner supplies.
18
Servicin g
D: Rem oval Of Bu rn er
A: Rem oval Of Hob Top
1. Follow the procedures in Section A.
2. With the aid a 12mm spanner loosen off the pipe
connection nut.
3. From the underside of the hob remove 2 self tapping
screws from the burner body.
1. Remove all control knobs, pan supports, burner caps
and burner crowns.
2. Remove 2 screws for each burner.
3. Remove 6 fixing screws from the pan support hinges,
and remove the hinges from the hob.
4. Lift hob top at the rear and disengage it from the
front locators.
4. Reassemble in reverse order and carry out leak test.
E: Rem oval of Ign it or
B: Rem oval Of t h e Hob Taps
(Isolat e Elect rical Su pply)
(Isolat e Elect rical Su pply)
1. Follow the procedures in Section A.
2. Remove H.T. leads from the ignitor by pulling tab
connection off. Disconnect supply cable from the
ignitor unit.
1. Follow the procedures in Section A.
2. With the aid of a 7mm spanner remove the clamping
bolt from the fixing clamp.
3. Loosen the pipe connection nut from the gas tap with
the aid of a 16mm spanner. Remove fixing clamps.
4. Reassemble in reverse order and carry out leak test.
3. With the aid of a pair of thin nose pliers, pull the
spring clip sideward off of the underside of the
ignitor
4. Reassemble in reverse order.
C: Rem oval Of Main s Term in al Block
(Isolat e Elect ric Su pply)
F: Rem oval of Ign it or Swit ch
(Isolat e Elect ric Su pply)
1. Follow the procedures in Section A.
2. Disconnect supply flex connections from terminal
block.
3. From the underside of the hob remove 1 self tapping
screw from the terminal block.
1. Follow the procedures in Section A.
2. Remove the fixing nut from the switch and remove
tab connections.
3. Reassemble in reverse order and check with wiring
diagram for correct reconnection.
4. Reassemble in reverse order.
Con version from Nat u ral Gas t o LPG
It is important to note that this model is designed for
use with natural gas but can be converted for use with
butane or propane gas providing the correct injectors
are fitted. The gas rate is adjusted to suit.
TO ADJ UST THE GAS RATE
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw, which is
located down the centre of the gas tap control shaft.
Upon completion stick the replacement rating plate
on the under side of the hob.
Met h od
• Ensure that the gas taps are in the 'OFF' position
• Isolate the hob from the electrical supply
• Remove all pan supports, burner caps, rings, crowns
and control knobs.
• With the aid of a 7mm box spanner the burner
injectors can then be unscrewed and replaced by the
appropriate LPG injectors.
IMPORTANT
The replacement/conversion of the gas hob should
only be undertaken by a competent person.
19
20
|