INSTALLATION INSTRUCTIONS
XANTECH VOLUME CONTROLS
XVCD50
XVCD100
XVCD100IR
XVCS50
XVCS100
XVCS100IR
XVC50
XVC100
XVCO100
Installation Instructions
XVC Series Volume Controls
Xantech’s premier product line of XV volume controls are in-wall
mountable stereo speaker volume control with impedance
matching capability. From one to eight pairs or stereo speakers
may be driven from one stereo power amplifier, using an equal
number of XV volume controls. It maintains correct impedance
matching between the amplifier and the speakers by the use of
instant setting jumpers on the control. This eliminates the need
for separate impedance matching components in multi-room
installations.
Features and Benefits
•
•
XVC50, XVD50, XVC50
Power handling: 50 Watts continuous, 150 Watts peak
XVC100, XVD100, XVCS100, XVCO100, XVCD100IR, XVCS100IR
Power handling: 100 Watts continuous, 300 Watts peak
• All Models
Adjustable impedance matching for up to 8 speaker pairs
(1, 2, 4, 8 pairs)
Attenuation:
11 steps plus Off; max 42 dB
20Hz-20kHz ±1 dB
16 gauge, Quick Connect (detachable)
Minimum 20 cu. in. J-box or Mud Ring.
Frequency response:
Speaker Terminals:
Mounting:
Note: Be sure to check fit before choosing J-boxes!
Isolated left- and right-channel grounds ensure safety with any bridged
amplifier.
Fluid, pop-free switching during volume adjustments.
Compatible with 4-, 6-, or 8-ohm speaker systems.
UL Listed to comply will all local building codes.
Installation requires only a screwdriver and wire strippers.
Impedance Jumper Settings for Identical
Impedance
How to use the impedance jumper setting chart:
1) Determine the minimum amplifier impedance (typically either
4- or 8-Ohm). This information can usually be found next to the
speaker outputs located on the receiver or amplifier. If in doubt,
consult the receiver and/or amplifier instruction manual.
2) Next, determine the impedance of a single speaker that will
be used. Use the left-most column.
3) Move to the right of the chart and find the number of speaker
pairs that you plan to connect to the volume control.
4) Finally, move up the column to the very top row. This row will
provide the jumper setting solution. Change the jumper on the
volume control to complete the impedance jumper setting
procedure. Both jumpers must be changed appropriately
(see diagram in Fig. 1)
Jumper Settings
x1
x2
x4
x8
8
Ohm
6
Ohm
4
1 PAIR 2 PAIRS 4 PAIRS 8 PAIRS
-
-
1 PAIR
1 PAIR
2 PAIRS 4 PAIRS
2 PAIRS 4 PAIRS
Ohm
CHART A: 8 Ohm Minimum Amplifier
Jumper Settings
x1
x2
x4
x8
-
8
Ohm
6
1 PAIR
4 PAIR
8 PAIRS
1 PAIR 2 PAIRS 4 PAIRS 8 PAIRS
Ohm
4
Ohm
1 PAIR 2 PAIRS 4 PAIRS 8 PAIRS
CHART B: 4 Ohm Minimum Amplifier
Example 1:
Two pairs of 8 Ohm ceiling speakers are to be used with two
volume controls, all driven by a single amplifier rated for 8 Ohm
minimum safe operating load impedance.
1) Refer to “CHART A”, 8 Ohm Minimum Amplifier.
2) In the first column, find “8 Ohms”.
3) Follow the row to the right until you find “2 PAIR”.
4) Follow the column up to the very top row and find that the
jumper setting should be set to “x2” for both volume
controls.
Installation Tip – Setting the Volume
1) Set your receiver and/or amplifier to the lowest possible
volume setting.
2) Turn all the volume controls to maximum volume (up
position for slider volume controls, full clockwise position
for rotary volume controls).
3) Turn up the receiver and/or amplifier volume setting until
you reach the maximum listening level desired.
4) Finally, lower the volume control level. Volume setting is
now complete.
Changing the Face Plate
1) Gently press the tabs
up on all four corners.
2) Lift the face plate off
the metal frame and
remove.
3) Replace with the
correct color face plate.
Single Zone, Single Speaker Pair
Volume Control Application
1X SETTING
Xantech PA series amplifier or equivalent
Jumper Settings
(Jumpers on Back)
I N P U T
+ R – L – L +
Left
Right
R+ R– L– L+
OUTPUT
R+
R–
L– L+
Fig 1.
Right
Left
Multiple Zone, Single Speaker Pair
Volume Control Application
Jumper Settings
(Jumpers on Back)
Fig 2.
Xantech PA series amplifier or equivalent
Left
Right
CB18
1
2
4
5
6
9
I N P U T
+ R – L – L +
I N P U T
+ R – L – L +
I N P U T
+ R – L – L +
I N P U T
+ R – L – L +
R+ R– L– L+
OUTPUT
R+ R– L– L+
OUTPUT
R+ R– L– L+
OUTPUT
R+ R– L– L+
OUTPUT
R+ R–
L– L+
R+ R–
L– L+
R+ R–
L– L+
R+ R–
L– L+
Right
Left
Right
Left
Right
Right
Left
Left
PAIR 1
PAIR 2
PAIR 3
PAIR 4
Single Zone, Single Speaker Pair
Volume Control and IR Receiver Application
1X SETTING
Fig 3.
Xantech PA series amplifier or equivalent
CD Player
I N P U T
R + R – L – L +
Hand Held
Remote
781RG
Power Supply
EMITTERS
789-44
CONNECTING BLOCK
®
•
78944
Connecting Block
SYLMAR,CA
MADE IN U.S.A.
IR
RCVR
PWR
R+ R– L– L+
OUTPUT
R+
R–
L–
L+
Right Speaker
Left Speaker
Note: Applies to Model XVCD100IR, XVCS100IR only
CB18 Connecting Block (not included)
The CB18 provides a convenient way to parallel many wires
onto a 4 conductor bus. You can easily connect many home run
leads from volume controls to the output terminals of a main
amplifier.
The CB18 features the following:
-
-
-
Nine 4-terminal plug-in connectors on a 4-conductor bus.
One-in eight-out or eight-in one-out capability.
Adhesive backed labels are included for attachment to
the plug-in terminals so that the speaker lead
connections can easily be identified.
-
High current design allows amplifiers rated as high as
500 Watts to be used.
-
-
Screw terminals handle wire sizes from 24 to 12 gauge.
Dimensions: 11-¼” x 1-¼” x 1-¼”.
Warranty Statement
Xantech 5 Year Limited Warranty
(Effective for products sold after July 1, 2006)
Xantech Corporation (“Xantech”) warrants to the holder of a valid proof of purchase as the first
end-user purchaser (“You”), its products to be free from defects in materials and workmanship
for the periods specified above from the date of purchase. This limited warranty extends only to
You for product purchased and used in the United States of America. For product purchased
outside of the United States of America, the terms of this warranty apply EXCEPT that You must
contact the Xantech authorized distributor in your region for warranty services. Product is not
intended for end user installation. If within the applicable warranty period above You discover
such item was not as warranted above and You promptly notify Xantech in writing, Xantech shall
repair or replace the items at its option. Xantech may elect which remedy or combination of
remedies to provide in its sole discretion. Xantech may use functionally equivalent
reconditioned/refurbished/pre-owned or new products or parts under this limited warranty. This
warranty shall not apply (a) to product which shall have been installed by other than an
authorized Xantech installer, (b) to installed product which is not installed to Xantech’s
specifications, (c) to product which shall have been repaired or altered by others than
Xantech, (d) to charges for installation or set up or adjustment of customer controls, (e) to
product that has suffered normal cosmetic deterioration (f) to product which shall have been
subjected to negligence, misuse, abuse, accident, or damage by circumstances beyond
Xantech’s control, including, but not limited to, lightning, flood, electrical surge, tornado,
earthquake, or any other catastrophic events beyond Xantech’s control, or (g) to product which
shall have been subjected to improper operation, connected equipment failure or malfunction,
inadequate packing or shipping damage, maintenance or storage, or to other than normal use of
service. The foregoing warranties do not cover reimbursement for labor, transportation, shipping,
removal, installation, or other expenses which may be incurred in connection with repair or
replacement. All claims for product shipping damage must be processes within 3 days of receipt
by You. A Xantech Return Authorization (RA) must be obtained from Xantech by You, your
installer or your distributor for Product covered under this warranty. Covered product must be
sent to Xantech together with proof of purchase, RA number, prepaid and insured to Xantech.
Freight collect shipments will be refused. Risk of loss or damage in transit is borne by the
sender. Xantech's warranty does not cover Products which have been received improperly
packaged, altered, or physically damaged. Products will be inspected upon receipt. Except as
may be expressly provided and authorized in writing by Xantech, Xantech shall not be subject to
any other obligations or liabilities whatsoever with respect to equipment manufactured or sold by
Xantech or services rendered by Xantech.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
EXPRESSED AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
ATTENTION: TO OUR VALUED CONSUMERS
To insure that consumers obtain quality pre-sale and after-sale support and service, Xantech
products are sold exclusively through authorized dealers and authorized distributors. Xantech
products are not sold online. The warranties on Xantech products are NOT VALID if the products
have been purchased from an unauthorized distributor or an online E-tailer. In order to
determine if your Xantech re-seller is authorized, please call Xantech (800) 843 - 5465.
Xantech Corporation
13100 Telfair Avenue, 2/F
Sylmar, CA 91342
Installation Instructions, Volume Controls
© 2006 Xantech Corporation, Document #08905078A
This document is copyright protected. No part of this manual may be copied or reproduced in
any form without prior written consent from Xantech Corporation.
Xantech Corporation shall not be liable for operational, technical, or editorial errors/omissions
made in this document.
|