R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
GHT 195
GHT 225
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Copyright E2003 Electrolux Home Products, Inc.
530164003
10/9/03
WARNING:
Blades can throw objects violently.
D You can be blinded or injured.
D Wear safety glasses.
Safety
Glasses
Boots
WARNING:
Hazard zone for thrown objects
D Blades can throw objects violently.
D Others can be blinded or injured.
D Keep people and animals 30 feet
(10 m) away.
30 ft.
(10 m)
Blades move Allow blades to stop
momentarily before removing
e them from the cut.
s
WARNING:
Blades move momentarily after the
trigger is released.
D The blades can seriously cut you or
others.
D Allow blades to stop before
removing them from the cut.
d.
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped witha spark arresting screen. If you
operatein alocalewhere such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by an autho-
rized service dealer.
D Store the unit so the cutting blade cannot
accidentally cause injury.
D Store in a dry area out of reach of children.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swelling. Prolonged use in cold
weather has beenlinked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
ASSEMBLY
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
ASSEMBLY
Your hedge trimmer is fully assembled; no as-
sembly is required.
-- 3 --
OPERATION
KNOW YOUR HEDGE TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the vari-
ous controls and adjustments. Save this manual for future reference.
Muffler
ON/OFF
Switch
Spark Plug
Throttle Lock
Hand Guard
Throttle
Lock--out
Throttle
Trigger
Primer Bulb
Fuel Mix Fill Cap
Choke Lever
ON/OFF SWITCH
PRIMER BULB
The ON/OFF SWITCH is used to stop the en-
gine. To stop engine, move switch to OFF.
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original position.
CHOKE
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving choke lever to the desired position. See
STARTING YOUR ENGINE for complete start-
ing information.
THROTTLE TRIGGER
The THROTTLE TRIGGER controls engine
speed. Squeeze the trigger for full speed opera-
tion; release it for idle speed.
IMPORTANT
WARNING: Muffler is very hot during
and after use. Do not touch the muffler or al-
low combustible material such as dry grass or
fuel to do so.
Experience indicates that alcohol blended fuels
(called gasohol or using ethanol or methanol)
can attract moisture which leads to separation
and formation of acids during storage. Acidic
gas can damage the fuel system of an engine
while in storage. To avoid engine problems,
empty the fuel system before storage for 30
days or longer. Drain the gas tank, start the en-
gine and let it run until the fuel lines and carbure-
tor are empty. Use fresh fuel next season.
Never use engine or carburetor cleaner prod-
ucts in the fuel tank or permanent damage
may occur.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 30 seconds at full
throttle. Releasing the trigger and allowing
the engine to briefly return to idle speed (5 --
10 seconds) will be sufficient.
This engine is certified to operate on un-
leaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/Weed Eater
brand synthetic oil is recommended. A 40:1
ratio is obtained by mixing 3.2 ounces (95 ml)
of oil with 1 gallon (4 liters) of unleaded gaso-
line). DO NOT USE automotive oil or boat oil.
These oils will cause engine damage. When
mixing fuel, follow instructions printed on oil
container. Once oil is added to gasoline,
shake container momentarily to assure that
the fuel is thoroughly mixed. Always read and
follow the safety rules listed under HANDLE
FUEL WITH CAUTION.
IMPORTANT POINTS
S Use the minimum throttle speed necessary
to effectively cut hedges for optimal hedge
trimmer performance.
S Never attempt to use this hedge trimmer to
cut hedges that have any branches with a
diameter larger than 7/16″.
-- 4 --
3. Slowly press the primer bulb 6 times.
4. Move the chokelever to the FULL CHOKE
position.
OPERATING POSITION
Hearing
Protection
ion
Primer Bulb
Choke
Lever
STOPPING YOUR ENGINE
D To stop the engine, move the ON/OFF
switch to the OFF position.
STARTING YOUR ENGINE
D Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
5. Pull starter rope handle sharply until en-
gine sounds as if it is trying to run, but do
not pull rope more than 6 times.
D Hold the unit on the ground in the starting
position as shown. Support unit so the
blade is off of the ground and away from
trees, bushes, onlookers, etc.
6. Move the choke lever to the HALF
CHOKE position.
7. Pull starter rope sharply until the engine
runs, but no more than 6 pulls.
NOTE:If the enginedoesn’t start after 6 pulls
(at the HALF CHOKE position), check to
make sure the ON/OFF switch is in the ON
position. Move the choke lever to the FULL
CHOKE position and press the primer bulb 6
times; pull the starter rope 2 more times.
Move the choke lever to the HALF CHOKE
position and pull the starter rope until the en-
gine runs, but no more than 6 more pulls. If
the engine still doesn’t start, it is probably
flooded. Proceed to STARTING A FLOODED
ENGINE.
8. Once the engine starts, allow the engine to
run 10 seconds, then move the choke lever
to the OFF CHOKE position. Allow the unit to
run for 30 more seconds at the OFF CHOKE
position before squeezing and releasing the
throttle trigger to release the throttle lock.
NOTE: If engine dies with the choke lever in
the OFF CHOKE position, movethe choke le-
ver to the HALF CHOKE position and pull the
rope until the engine runs, but no more than 6
pulls.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
Throttle Lock
Throttle
Lock-out
Throttle
Trigger
1. Move the ON/OFF switch to the ON posi-
tion.
STARTING A WARM ENGINE
1. Move the ON/OFF switch to the ON posi-
tion.
2. Engage the throttle lock as follows:
D press the throttle lock--out;
D squeeze and hold throttle trigger;
D press and hold throttle lock, then
D release the throttle trigger
NOTE: Keep the throttle lock engaged until
the engine starts.
2. Slowly press the primer bulb 6 times.
3. Move the choke lever to the HALF
CHOKE position.
4. Engage the throttle lock as directed in
STARTING A COLD ENGINE.
NOTE: Keep the throttle lock engaged until
the engine starts.
ON
OFF
5. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
Switch
6. Allow the engine to run 10 seconds, then
move the choke lever to the OFF CHOKE
position.
7. Release the throttle lock by squeezing and
releasing the trigger.
NOTE: If engine has not started, pull starter
rope 5more pulls. If engine still does not run, it
is probably flooded. Proceed to STARTING A
FLOODED ENGINE.
-- 5 --
pull the rope to clear the engine of excess
fuel. Starting could require pulling the starter
rope many times depending on how badly the
unit is flooded. If the unit still doesn’t start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the ON/OFF switch inthe ON position and the
choke lever in the OFF CHOKE position and
engaging the throttle lock as directed in the
STARTING A COLD ENGINE section; then,
SERVICE
Cleaning the air filter:
WARNING: Ensure ON/OFF switch
is in the OFF position and disconnect the
spark plug before performing maintenance
except for carburetor adjustments.
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
S Clean the cover and the area around it to
keep debris from falling into the carburetor
chamber when the cover is removed.
S Remove parts as illustrated.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
NOTE: Do not clean filter in gasoline or other
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emis-
sions.
S Wash the filter in soap and water.
S Allow filter to dry.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Add a few drops of oil to the filter; squeeze
filter to distribute oil.
S Replace parts.
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
CHECK FOR DAMAGED OR
WORN PARTS
WARNING: The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen and
must be removed to avoid creating a fire haz-
ard or affecting engine performance.
For normal homeowner use, the muffler and
spark arresting screen will not require any
service. After 50 hours of use, we recom-
mend that your muffler be serviced or re-
placed by an authorized service dealer.
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/OFF Switch -- Ensure ON/OFF switch
functions properly by moving the switch to the
OFF position. Make sure engine stops; then
restart engine and continue.
S Fuel Tank -- Do not use unit if fuel tank shows
signs of damage or leaks.
INSPECT AND CLEAN UNIT AND
LABELS
S Before and after each use, inspect com-
plete unit for loose or damaged parts. After
each use, clean the unit and labels using a
damp cloth with a mild detergent.
S Wipe off unit with a clean dry cloth.
CARBURETOR ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The blade
will be moving during most of this procedure.
Wear your protective equipment and observe
all safety precautions. When making adjust-
ments, use a screwdriver short enough to
keep your hands behind the handguard and
away from the blade. After making adjust-
ments, the blade must not move at idlespeed.
The carburetor has been carefully set at the
factory. Adjustments may benecessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is re-
leased.
CLEAN AIR FILTER
Air Filter
Cover
S The blade moves at idle. Keep others away
when making idle speed adjustments.
Make adjustments with the unit resting on a
level surface free of debris that can be caught
in the hedge trimmer blade. Serious injury to
the operator and others can occur if the car-
buretor is not properly adjusted. Keep all
parts of your body away from the blade and
muffler.
Air Filter
Screw
-- 6 --
If you require further assistanceor are unsure
about performing this procedure, contact an
Idle Speed Adjustment
Allow engine to idle. Adjust speed until engine
runs without blade moving(idle too fast) or en-
gine stalling (idle speed too slow).
S Turn idle speed screw clockwise to in-
crease engine speed if engine stalls or dies.
S Turn idle speed screw counterclockwise to
decrease engine speed if the blade moves
at idle.
authorized
service
dealer
or
call
1--800--554--6723.
REPLACE SPARK PLUG
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
WARNING: Recheck the idle speed
after each adjustment. The blade must not
move at idle speed to avoid serious injury to
the operator or others.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
4. Reinstall the spark plug boot.
REPLACE FUEL FILTER
Toreplacefuelfilter, drain unit by running it dry
of fuel, then remove fuel cap/retainer assem-
bly from tank. Pull filter from tank and remove
it fromthe fuelline. Install new fuel filter onfuel
line; reinstall parts.
Idle Speed Screw
Fuel Filter
Fuel Line
STORAGE
S Ensure ON/OFF switch is in the OFF posi-
tion.
S Disconnect the spark plug wire.
S Apply a light machine oil along the edge of
the top strap as shown.
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
OIL
S Store unit and fuel well out of the reach of
children.
Top Strap
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit.
FUEL SYSTEM
S Store in a clean dry area.
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la-
beled IMPORTANT regarding the use of ga-
sohol in your engine. Fuel stabilizer is an ac-
ceptable alternative in minimizing the formation
of fuel gum deposits during storage. Add stabi-
lizer to gasoline in fuel tank or fuel storage con-
tainer. Follow the mix instructions found on sta-
bilizer container. Run engine at least 5 minutes
after adding stabilizer.
S Clean all parts and check for damage.
Have damaged parts repaired or replaced
by an authorized service dealer.
S Keep all nuts, bolts, and screws tight.
S Lightly oil external metal surfaces, includ-
ing the blade.
To oil the blade, do the following:
S Stop the engine and allow blade to come to
a complete stop.
-- 7 --
ENGINE
OTHER
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range (see RE-
PLACE SPARK PLUG section).
S Clean air filter.
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
NEED ASSISTANCE?
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having theproper gasoline to
oil ratio.
NEED ASSISTANCE?
Call 1-800-554-6723 for assistance.
NEED SERVICE PARTS?
Contact your dealer.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performingall of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. ON/OFF switch in the
OFF position.
2. Engine flooded.
1. Move ON/OFF switch to the ON
position.
2. See “Starting a Flooded Engine”
in Operation Section.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6. Compression low.
6. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
Engine will not
accelerate,
lacks power,
or dies under
a load.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
1. Adjust choke.
2. Fuel mixture incorrect.
2. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine runs
hot.
1. See “Fueling Engine” in Operation
section.
1. Fuel mixture incorrect.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
4. Contact an authorized service dealer.
-- 8 --
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
cover predelivery setup or normal adjustments
warrants to the original purchaser that each new
Weed Eater brand gasoline tool or attachment
is free from defects in material and workman-
ship and agrees to repair or replace under this
warranty any defective gasoline product or at-
tachment as follows from the original date of
purchase.
explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of ELECTROLUX HOME PRO-
DUCTS, INC., is to continuously improve its
products. Therefore, ELECTROLUX HOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, de-
signs, specifications, and accessories of all
products at any time without notice or obligation
to any purchaser.
2 YEARS -- Parts and Labor, when used for
household purposes.
60 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically
recommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Additionally,
this warranty does not cover tune--ups, spark
plugs, filters, starter ropes, starter springs, cut-
ting line, or rotating head parts that will wear and
require replacement with reasonable use during
the warranty period. This warranty does not
U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency/California Air Resources
Board, Environment Canada and ELECTRO-
LUX HOME PRODUCTS, INC., are pleased
to explain the emissions control system war-
ranty on your year 2002--2004 small off--road
engine. In California, all small off--road en-
gines must be designed, built, and equipped
to meet the State’s stringent anti--smog stan-
dards. ELECTROLUX HOME PRODUCTS,
INC., must warrant the emission control sys-
tem on your smalloff--road engine for the peri-
ods of time listed below provided there has
been no abuse, neglect, or improper mainte-
nance of your small off--road engine. Your
emission control system includes parts such
as the carburetor and the ignition system.
Where a warrantable condition exists, ELEC-
TROLUX HOME PRODUCTS, INC., will re-
pair your small off--road engine engine at no
cost to you. Expenses covered under warran-
ty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COV-
ERAGE: If any emissions relatedpart onyour
engine (as listed under Emissions Control
Warranty Parts List) is defective or a defect in
the materials or workmanship of the engine
causes the failure of suchan emissionrelated
part, the part will be repaired or replaced by
ELECTROLUX HOME PRODUCTS, INC.
OWNER’S WARRANTY RESPONSIBILI-
TIES: As the small off--road engine engine
owner, you are responsible for the perfor-
mance of the required maintenance listed in
your instruction manual. ELECTROLUX
HOME PRODUCTS, INC., recommends that
you retain all receipts covering maintenance
on your small off--road engine, but ELEC-
TROLUX HOME PRODUCTS, INC., cannot
deny warranty solely for the lack of receipts or
for your failure to ensure the performance of
all scheduled maintenance. As the small off--
road engine engine owner, you should be
aware that ELECTROLUX HOME PROD-
UCTS, INC., may deny you warranty cover-
age if your small off--road engine engine or a
part of it has failed due to abuse, neglect, im-
proper maintenance, unapproved modifica-
tions, or the use of parts not made or ap-
proved by the original equipment manufactur-
er. You are responsible for presenting your
small off--road engine to an ELECTROLUX
HOME PRODUCTS, INC., authorized repair
center as soon as a problem exists. Warranty
repairs should be completed in a reasonable
amount of time, not to exceed 30 days. If you
have any questions regarding your warranty
rights andresponsibilities, you shouldcontact
your nearest authorized service center or call
ELECTROLUX HOMEPRODUCTS, INC., at
1--800--554--6723.
WARRANTY COM-
MENCEMENT DATE: The warranty period
begins on the date the small off--road engine
is purchased. LENGTH OF COVERAGE:
This warranty shall be for a period of two
years fromthe initial date of purchase. WHAT
IS COVERED: REPAIR OR REPLACE-
MENT OF PARTS. Repair or replacement of
any warranted part will be performed at no
charge to the owner at an approved ELEC-
TROLUX HOME PRODUCTS, INC., servic-
-- 9 --
ing center. If you have any questions regard-
ing your warranty rights and responsibilities,
you should contact your nearest authorized
service center or call ELECTROLUX HOME
PRODUCTS, INC., at 1--800--554--6723
WARRANTY PERIOD: Any warranted part
which is not scheduled for replacement as re-
quired maintenance, or which is scheduled
only for regular inspection to the effect of “re-
pair or replace as necessary” shall be war-
ranted for 2 years. Any warranted part which
is scheduled for replacement as required
maintenance shallbe warranted for the period
of time up to the first scheduled replacement
point for that part. DIAGNOSIS: The owner
shall not be charged for diagnostic labor
which leads to the determination that a war-
ranted part is defective if the diagnostic work
is performed at an approved ELECTROLUX
HOME PRODUCTS, INC., servicing center.
CONSEQUENTIAL DAMAGES: ELEC-
TROLUX HOME PRODUCTS, INC., may be
liable for damages to other engine compo-
nents caused by the failure of a warranted
part still under warranty. WHAT IS NOT COV-
ERED: All failures caused by abuse, neglect,
or improper maintenance are not covered.
ADD-ON OR MODIFIED PARTS: The use
of add--on or modified parts can be grounds
for disallowing a warranty claim. ELECTRO-
LUX HOME PRODUCTS, INC., is not liable
to cover failures of warranted parts caused by
the use of add--on or modifiedparts. HOWTO
FILE A CLAIM: If you have any questions re-
garding your warranty rights and responsibili-
ties, you should contact your nearest autho-
rized service center or call ELECTROLUX
HOME
PRODUCTS,
INC.,
at
1--800--554--6723. WHERE TO GET WAR-
RANTY SERVICE: Warranty services or re-
pairs shall be provided at all ELECTROLUX
HOME PRODUCTS, INC., service centers.
Call: 1--800--554--6723 MAINTENANCE,
REPLACEMENT AND REPAIR OF EMIS-
SION RELATED PARTS: Any ELECTRO-
LUX HOME PRODUCTS, INC., approved re-
placement part used in the performance of
any warranty maintenance or repair on emis-
sion related parts will be provided without
charge to the owner if the part is under war-
ranty. EMISSION CONTROL WARRANTY
PARTS LIST: Carburetor, Ignition System:
Spark Plug (covered up to maintenance
schedule), Ignition Module, Muffler including
catalyst. MAINTENANCE STATEMENT:
The owner is responsible for the performance
of all required maintenance as defined in the
instruction manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
-- 1 0 --
|